Batt Con >NAME >VALUE Power Switch Add LED Res >NAME Switch PB >NAME Speak Pot Mic SD Shield + Uno Battery Pack Connector >NAME >VALUE Resistor >NAME >NAME PB Speak Pot Mic Module >name <b>Supply Symbols</b><p> GND, VCC, 0V, +5V, -5V, etc.<p> Please keep in mind, that these devices are necessary for the automatic wiring of the supply signals.<p> The pin name defined in the symbol is identical to the net which is to be wired automatically.<p> In this library the device names are the same as the pin names of the symbols, therefore the correct signal names appear next to the supply symbols in the schematic.<p> <author>Created by librarian@cadsoft.de</author> >VALUE >VALUE >VALUE >VALUE <b>SUPPLY SYMBOL</b> <b>SUPPLY SYMBOL</b> <b>SUPPLY SYMBOL</b> <b>SUPPLY SYMBOL</b> <b>Test Pins/Pads</b><p> Cream on SMD OFF.<br> new: Attribute TP_SIGNAL_NAME<br> <author>Created by librarian@cadsoft.de</author> <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME <b>TEST PAD</b> >NAME >VALUE >TP_SIGNAL_NAME TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD TEST PAD >NAME >TP_SIGNAL_NAME <b>Test pad</b> Since Version 8.2, EAGLE supports online libraries. The ids of those online libraries will not be understood (or retained) with this version. Since Version 8.3, EAGLE supports URNs for individual library assets (packages, symbols, and devices). The URNs of those assets will not be understood (or retained) with this version. Since Version 8.3, EAGLE supports the association of 3D packages with devices in libraries, schematics, and board files. Those 3D packages will not be understood (or retained) with this version.